Abocom 802.11 b/g/n Mini Wireless LAN USB 2.0 Adapter Non Bedienungsanleitung

802.11 b/g/n Mini Wireless LAN USB 2.0 Adapter User’s Manual

- 6 - For Windows Vista Install the Software Note: Do not insert the Wireless LAN USB Adapter into the computer until the InstallShield Wizard fin

- 7 - 3. When prompt to the following message, please click Install to begin the installation. 4. When the following screen appears, click Fini

- 8 - Install the Hardware Note: Insert the Wireless LAN USB Adapter when finished software installation. Insert the Wireless LAN USB Adapter into

- 9 - Network Connection IP Address Note: When assigning IP address(es) to computers on the network, remember to have IP address for each computer s

- 10 - Chapter 3: Utility Configuration For Windows 2000/XP After the Wireless LAN USB Adapter has been successfully installed, users can use the in

- 11 - Station Mode IMPORTANT NOTICE: Under screen resolution 800 x 600 pixels, if users click the triangle button at the right down corner of the

- 12 - Encryption Shows the encryption type. Use 802.1x Whether or not use 802.1x feature. Tx Power Transmit power, the amount of power used by a

- 13 - • The Ad-hoc lets users set a small wireless workgroup easily and quickly. Equipped with the Wireless LAN USB Adapter, users can share files

- 14 - • Shared: Shared key is when both the sender and the recipient share a secret key. • LEAP: Light Extensible Authentication Protocol. It is

- 15 - EAP Method: • PEAP: Protect Extensible Authentication Protocol. PEAP transport securely authentication data by using tunnelling between PEAP

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital dev

- 16 - ID/ PASSWORD: Identity and password for server. • Authentication ID / Password: Identity, password and domain name for server. Only "EAP

- 17 - Delete Click to delete an existing profile. Edit Click to edit a profile. Activate Click to make a connection between devices. Network The

- 18 - Add to Profile Select an item (SSID) on the list and then click to add it into the profile list. Connect Select an item (SSID) on the list and

- 19 - Selected Registrar: Indicate if the user has recently activated a Registrar to add an Enrollee. The values are "TRUE" and "FALS

- 20 - Link Status Tab Status Shows the current connected AP SSID and MAC address. If there is no connection existing, it will show Disconnected. Ex

- 21 - Signal Strength 1 Shows the receiving signal strength, users can choose to display as percentage or dBm format. Noise Strength Shows the noise

- 22 - Enable CCX (Cisco Compatible extensions) Check to enable the CCX function. • Turn on CCKM. • Enable Radio Measurements: Check to enabl

- 23 - Receive Statistics Frames Received Successfully Shows information of packets received successfully. Frames Received With CRC Error Shows info

- 24 - WMM/QoS Tab WMM Enable Check the box to enable Wi-Fi Multi-Media function that is meant to improve audio, video and voice applications transmi

- 25 - WPS Tab WPS AP List Display the information of surrounding APs with WPS IE from last scan result. List information included SSID, BSSID, Chan

Table of Contents CHAPTER 1: INTRODUCTION ...1 FEATURES ...

- 26 - If selected the AP that listed in the WPS Profile List field, users can click the Detail button to see more AP information. SSID: Shows the c

- 27 - Export Profile Export all credentials to Profile. Delete Delete an existing credential. And then select the next credential if exist. If there

- 28 - About This page displays the information of the Wireless LAN USB Adapter including, Config Version/ Date, Driver Version/ Date, EEPROM Versio

- 29 - Soft AP mode Config Config SSID AP name of user type. Users also can click Use Mac Address button to display it. Channel Manually force the

- 30 - Authentication Type: There are several types of authentication modes including Open, Shared, WPA-PSK, WPA2-PSK, and WPA-PSK/ WPA2-PSK. (Syste

- 31 - No forwarding among wireless clients No beacon among wireless client, clients can share information each other. (The system default is no for

- 32 - Access Control Access Policy User chooses whether AP start the function or not. (System default is Disable.) z Disable: Do not use this acces

- 33 - MAC Table MAC Address The station MAC address of current connection. AID Raise value by current connection. Power Saving Mode The station of c

- 34 - Statistics Transmit Statistics Frames Transmitted Successfully Shows information of packets successfully sent. Frames Fail To Receive ACK Aft

- 35 - Duplicate Frames Received The number of duplicate packets received. Reset Counter Reset counters to zero. About This page displays the Wirel

Statistics...34 About...

- 36 - For Windows Vista After the Wireless LAN USB Adapter has been successfully installed, users can use the included Configuration Utility to set

- 37 - Station Mode Profile Profile can book keeping the favorite wireless setting among home, office, and other public hot-spot. Users may save mult

- 38 - Power Save Mode Choose from CAM (Constantly Awake Mode) or PSM (Power Saving Mode.) RTS Threshold Shows the RTS Threshold of the device. Fragm

- 39 - frame delimiter. Select from the pull-down menu to change the Preamble type into Auto or Long. Power Save Mode: • CAM (Constantly Awake Mode)

- 40 - • WPA/ WPA-PSK/ WPA2/ WPA2-PSK: WPA-PSK offers two encryption methods, TKIP and AES. Select the type of algorithm, TKIP or AES and then enter

- 41 - certificate-based and mutual authentication of the client and the network. It relies on client-side and server-side certificates to perform au

- 42 - OK: Click to save settings and exit this page. Cancel: Click to call off the settings and exit. Server Certification tab: Use certificate c

- 43 - Network Tab Sorted by Indicate that AP list are sorted by SSID, Channel or Signal. Show dBm Check the box to show the dBm of the AP list. SSID

- 44 - WPS WPS information contains Authentication Type, Encryption Type, Config Methods, Device Password ID, Selected Registrar, State, Version, AP

- 45 - 802.11n This tab will show up if the selected access point supports 11n mode. Here shows the connected access point 802.11n related informati

- 1 - Chapter 1: Introduction The 802.11 b/g/n Mini Wireless LAN USB 2.0 Adapter (Wireless LAN USB Adapter) is an IEEE802.11b/g/n USB adapter that c

- 46 - Link Status Tab Status Shows the current connected AP SSID and MAC address. If there is no connection existing, it will show Disconnected. Ext

- 47 - Advanced Tab Wireless mode Here supports 2.4G (included 802.11b/g/n) wireless mode. Enable TX Burst Check to enable this function. This funct

- 48 - Transmit Statistics Tab Frames Transmitted Successfully Shows information of packets successfully sent. Frames Retransmitted Successfully Show

- 49 - WMM/ QoS The WMM page shows the Wi-Fi Multi-Media power save function and Direct Link Setup that ensure the wireless network linking quality.

- 50 - WPS The primary goal of Wi-Fi Protected Setup (Wi-Fi Simple Configuration) is to simplify the security setup and management of Wi-Fi networks.

- 51 - Config Mode Select from the pull-down menu to decide the station role-playing as an Enrollee or an external Registrar. Detail Click the Detail

- 52 - Rotate Command to rotate to connect to the next network inside credentials. Disconnect Stop WPS action and disconnect this active link. And th

- 53 - Radio On/Off Click this button to turn on or off radio function. This icon shows radio on, click to turn it off. This icon shows radio off,

- 54 - Utility Menu List To access Windows Vista utility menu list, please right click the utility icon on the task bar. z Launch Config Utility:

- 55 - Soft AP mode Config Config SSID AP name of user type. Users also can click Use Mac Address button to display it. Channel Manually force t

- 2 - Chapter 2: Installation For Windows 2000/XP Install the Software Note: Do not insert the Wireless LAN USB Adapter into the computer until th

- 56 - Authentication Type: There are several types of authentication modes including Open, Shared, WPA-PSK, WPA2-PSK, and WPA-PSK/ WPA2-PSK. (Syste

- 57 - No forwarding among wireless clients No beacon among wireless client, clients can share information each other. (The system default is no forw

- 58 - Access Control Access Policy User chooses whether AP start the function or not. (System default is Disable.) z Disable: Do not use this acces

- 59 - MAC Table MAC Address The station MAC address of current connection. AID Raise value by current connection. Power Saving Mode The station of

- 60 - Statistics Transmit Statistics Frames Transmitted Successfully Shows information of packets successfully sent. Frames Fail To Receive ACK Aft

- 61 - Duplicate Frames Received The number of duplicate packets received. Reset Counter Reset counters to zero. About This page displays the Wirel

- 62 - Chapter 4: UNINSTALLATION For Windows 2000/XP To uninstall the utility and driver, please refer to below steps. (When uninstalling the utilit

- 63 - 2. Click Yes to complete remove the selected application and all of its features. 3. Then click Finish to complete the uninstallation.

- 64 - For Windows Vista To uninstall the utility and driver, please refer to below steps. (When uninstalling the utility, the driver will be uninst

- 65 - 2. Click Yes to complete remove the selected application and all of its features. Caution: Under Vista 64-bit operation system, when proc

- 3 - 3. Select the check box to choose a Configuration Tool from the listed two choices. z Configuration Tool: Choose to use the configuration uti

- 4 - 6. When the following screen appears, click Finish to complete the software installation. Install the Hardware Note: Insert the Wireless

- 5 - Verification To verify if the device is active in the computer. Go to Start > Setting > Control Panel > System > Hardware > Devi